PowerPoint Presentation Unit 61 Interior Trim Wood Molding

PowerPoint Presentation Unit 61 Interior Trim Wood Molding

PowerPoint Presentation Unit 61 Interior Trim Wood Molding Composite Molding Trimming Door Openings Trimming Window Openings Installing Base Molding Installing Ceiling Molding

Unit 61 Interior Trim Softwood and hardwood lumber are used in the manufacture of wood molding. Unit 61 Interior Trim

Wood moldings are trim pieces at the juncture of walls and ceilings and floor and walls, and at intersections of other materials. Unit 61 Interior Trim Molding is commonly

installed along the floor and around door and window openings. In some cases, ceiling molding is specified. Unit 61 Interior Trim

Door casing patterns may be contemporary or traditional in design. Door casing is usually backed out to produce a tight fit. Unit 61 Interior Trim Door casing is nailed to the trimmer stud and side jamb.

Unit 61 Interior Trim A 45 miter cut is usually required at the joints between the top piece and the side pieces of door casing.

Unit 61 Interior Trim When trimming a door opening, first mark the doorjamb at intervals for a 1/8 reveal.

Unit 61 Interior Trim More shrinkage occurs across the grain than along the grain of wood. Since there is more width at the heel than at

the toe of the miter, the heel of the miter joint opens up. Unit 61 Interior Trim Specialty clamps may be used to apply

pressure to a miter joint to allow the glued joint to reach its full strength. Unit 61 Interior Trim Interior window trim for wood-framed

windows may be either contemporary or traditional in design. Window trim should match door trim in the building. Unit 61 Interior Trim Traditional window trim requires a rabbeted stool. A variety of patterns

are available. Unit 61 Interior Trim When a stool and apron are installed, a corner return is used to conceal the end grain.

Unit 61 Interior Trim Base molding is held tightly to the finished floor and nailed to the bottom plate and studs. Unit 61 Interior Trim

Base molding is usually thinner than the door casing it butts against. Unit 61 Interior Trim Base molding may be applied with a base shoe

and base cap. Unit 61 Interior Trim For an inside corner fit, one piece of the base molding must be cut for proper fit.

Unit 61 Interior Trim A scarf joint produces the best fit between two pieces of base molding joined along a wall. Scarf joints should always be glued to limit separation.

Unit 61 Interior Trim When fitting base molding, first fit and cope the inside corner of one piece, then miter the outside corners.

Unit 61 Interior Trim The three basic profiles of ceiling molding are rectangular with a beveled edge, cove, and crown. Unit 61 Interior Trim

When installing crown molding, one of the inside corner pieces is coped. Unit 61 Interior Trim When cutting a 45

angle on crown molding, position the molding with the bottom edge pressed against the fence of the miter box.

Recently Viewed Presentations

  • Fatigue Nearly one quarter of American workers spend

    Fatigue Nearly one quarter of American workers spend

    Fighting against this natural circadian rhythm can cause both sleepiness and fatigue. PPT-SM-F 2018. ... Control the causes of fatigue to reduce your risk. Sleep is an important part of staying safe, make it a priority. PPT-SM-F 2018.
  • Designer protein enriched with large neutral amino acids: A ...

    Designer protein enriched with large neutral amino acids: A ...

    Selection of template - αs1 casein. ... Complete hydrolyzation with chymotrypsin, pepsin, and trypsin-good . in . silico. digestibility of the protein. High nutritional significance for PKU patients. Future work. Cloning and expression of the designer protein in . P.
  • Contributors to the Cell Theory

    Contributors to the Cell Theory

    Mitochondrion - ? trucking company power plant recycling center storage company fence surrounding city post office factory border patrol city hall restaurant A Cell Is Like A City Cell Membrane - Cell Wall - Nucleus - Ribosome - ER -...
  • SOUTH CAROLINA End of the Year Duties for

    SOUTH CAROLINA End of the Year Duties for

    Make sure a financial review/audit is done. Check the files! Study duties and reference to finances/budget in your PTA bylaws. ... Forms 990, 990-EZ, 990-N and 990-PF Due: 15th day of the 5th month after the organization's accounting period ends.
  • Session Title - Lenoir-Rhyne University

    Session Title - Lenoir-Rhyne University

    A database connection is necessary to connect from a non-SAP source to SLT (SAP Landscape Transformation) Tables can be loaded but they cannot be automatically replicated, meaning the addition of new tables or columns after the initial load must be...
  • Title of the presentation Prepared by Date (e.g. 10 November ...

    Title of the presentation Prepared by Date (e.g. 10 November ...

    Funded by the UK Government, SDC and Danida. 1. Need to aligh all the heading text box in each slide so that they are in same place. 1.3 Background: Overall Objective of the Project. To contribute to . poverty reduction....
  • CMU SCS GigaTensor: Scaling Tensor Analysis Up By

    CMU SCS GigaTensor: Scaling Tensor Analysis Up By

    Background: Tensor. Tensors (=multi-dimensional arrays) are everywhere. Sensor stream (time, location, type) Predicates (subject, verb, object) in knowledge base
  • Simple Text Mining Through Pattern Matching David Bayba

    Simple Text Mining Through Pattern Matching David Bayba

    A simple JMP script can search for the standard pattern for equipment IDs in these fields and write the results into new equipment ID fields. The accuracy of these findings can then be improved by automatically removing identified equipment IDs...